Show Posts
|
Pages: [1] 2 3 ... 14
|
1
|
General Category / General Forum / QSC musicspace ISA500Ti Power Amp เครื่องขยายเสียง
|
on: April 01, 2015, 04:39:35 am
|
QSC musicspace ISA500Ti Power Amp เครื่องขยายเสียง Brand : QSC Model : ISA500Ti ราคาปกติ : 35,900.00 บาท000000 ราคาพิเศษ. 29,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เพาเวอร์แอมป์ QSC ISA500TI
260W @ 8 Ohms Power Amplifier (with Isolated 25, 70, 100 Volt Outputs)Designed as a cost-effective solution specifically for sound contractors, the ISA500TI has isolated 25, 70 and 100 volt outputs for distributed audio systems, and a comprehensive feature set to make the ISA500TI a rugged, cost-effective power solution for any permanently installed sound system. Unique among distributed sound power amplifiers, the ISA500TI will drive 8- or 4-ohm loads and a distributed system on the same channel simultaneously. This enables a contractor to reduce the number of required amplifier channels by allowing a limited number of distributed speakers to be attached to the same amp as is powering the main sound system. Housed in a rugged 3-U chassis, all seven models feature rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings. Inputs include both XLR and detachable Euro-style connectors. Outputs feature covered barrier strip connectors for safety agency compliance, and for added versatility, a DataPort V2 (Version 2) terminated with an HD-15 connector is provided for use with DPV2-compatible signal processing accessories such as the XC-3 Crossover, SF-3 Subwoofer Filter, LF-3 Low Frequency Filter and the DSP-3 with external power supply. Selectable high-pass filters are included to protect speakers and prevent speaker transformer saturation with minimal effect on program material. The ISA500TI provides additional protection circuitry including DC, infrasonic, thermal overload, RF and short circuit protection. Features: Four models for low-impedance applications Three "Ti" versions include low-impedance and isolated 25, 70, and 100 volt outputs for distributed audio systems Rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings XLR and detachable Euro style input connectors DataPort V2 for use with DPV2-compatible signal processing accessories (XC-3, SF-3, LF-3) and DSP-3/DSP-4 (with external power supply) Independent defeatable clip limiters for reduced distortion Selectable high-pass filters protect speakers and prevent speaker transformer saturation with minimal effect on program material (30 Hz or 70 Hz on non-"Ti" models, 50 Hz or 75 Hz on "Ti" models) Front panel indicators include power, signal, and clip Covered barrier strip output connectors for safety agency compliance Automatic variable-speed fan for quiet normal operation with maximum cooling on demand Rear-to-front air flow keeps equipment racks cool Stereo, Bridge, or Parallel operating modes Comprehensive protection circuitry including DC, infrasonic, thermal overload and short circuit protection 3-year warranty plus optional 3-year extended service contract Specifications: 8 ohms 20Hz-20kHz 0.1% THD: 260W 4 ohms 20Hz-20kHz 0.1% THD: 425W 2 ohms 1kHz 1% THD: 700W 70V or 100V 50Hz-16kHz 0.5% THD: 500W 25V 50Hz-16kHz 0.5% THD: 300W Bridged Mono 8 ohms 1kHz 0.1% THD: 900W Bridged Mono 4 ohms 1kHz 1% THD: 1400W 140V or 200V 50 Hz-16kHz 0.5% THD: 1000W Signal to Noise (20Hz-20kHz): 100 dB Distortion (SMPTE-IM): < 0.01% Input Sensitivity @ 8 ohms: 1.07v (+2.8 dBu) Voltage Gain @ 8 ohms: 44.7x (33 dB) Output Circuitry: Class AB Distortion (Typical):
* 20 Hz-20 kHz: 10 dB below rated power: Less than 0.03% THD, 4 ohms and 8 ohms
* 1.0 kHz and below: full rated power: Less than 0.03% THD, 4 ohms and 8 ohms Frequency Response, 10dB below rated output power: 20Hz-20kHz, +0/-1dB, -3 dB points: 5 Hz + 50 Hz Damping Factor (Direct Outputs): > 250 @ 8 ohms Output Regulation: < 1.5 dB Input Impedance: 10 k ohms unbalanced, 20 k ohms balanced Input Clipping: 10 Vrms (+22 dBu) Cooling: Continuously variable speed fan, back-to-front air flow Connectors, each channel:
* Input: Active balanced; 3-pin Euro-style detachable terminal block and XLR (pin 2+)
* Output: Covered barrier strips
* DataPort V2: HD-15 connector Controls:
* Front: AC switch
* Rear: Ch. 1 and Ch. 2 gain knobs, 10-position DIP switch Indicators: PWR-ON Green LED, SIGNAL Green LED (1 per channel), CLIP Red LED (1 per channel) Amplifier Protection: Full short circuit, open circuit, thermal, ultrasonic, and RF protection; Stable into reactive or mismatched loads Power Requirements: 120, 230, VAC, 50-60 Hz Load Protection: On/off muting; Triac crowbar: ISA 750 Rack-mount size: 3 RU Dimensions: 19″ x 5.25″ x 15.9″ (48.3 x 13.3 x 40 cm) Weight: 49 lbs. (22.3 kg) หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
2
|
General Category / General Forum / QSC musicspace ISA300Ti Power Amp เครื่องขยายเสียง
|
on: April 01, 2015, 04:32:41 am
|
QSC musicspace ISA300Ti Power Amp เครื่องขยายเสียง Brand : QSC Model : ISA300Ti ราคาปกติ : 31,000.00 บาท000000 ราคาพิเศษ. 25,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เพาเวอร์แอมป์ QSC ISA300TI
Power Amplifier, 185 W/Ch 8 Ohms, 70v/100vDesigned as a cost-effective solution specifically for sound contractors, the ISA Series features seven models including four low impedance models (ISA 280, ISA 450, ISA 750) rated for 2-ohm operation, and three "Ti" versions with isolated 25, 70 and 100 volt outputs for distributed audio systems (ISA 300Ti, ISA 500Ti, ISA 800Ti). Versatile loading options and a comprehensive feature set make the ISA Series a rugged, cost-effective power solution for any permanently installed sound system. Unique among distributed sound power amplifiers, the "Ti" versions will drive 8- or 4-ohm loads and a distributed system on the same channel simultaneously. This enables a contractor to reduce the number of required amplifier channels by allowing a limited number of distributed speakers to be attached to the same amp as is powering the main sound system. Housed in a rugged 3-U chassis, all seven models feature rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings. Inputs include both XLR and detachable Euro-style connectors. Outputs feature covered barrier strip connectors for safety agency compliance, and for added versatility, a DataPort V2 (Version 2) terminated with an HD-15 connector is provided for use with DPV2-compatible signal processing accessories such as the XC-3 Crossover, SF-3 Subwoofer Filter, LF-3 Low Frequency Filter and the DSP-3 with external power supply. Selectable high-pass filters are included to protect speakers and prevent speaker transformer saturation with minimal effect on program material. The ISA Series provide additional protection circuitry including DC, infrasonic, thermal overload, RF and short circuit protection. On the ISA 750 and ISA 800Ti, class H complementary bipolar output circuitry increases system efficiency by reducing AC power draw and waste heat by 40%. Cooling is accomplished via an automatic variable speed fan, which pulls air from back to front. Features: Four models for low-impedance applications Three "Ti" versions include low-impedance and isolated 25, 70, and 100 volt outputs for distributed audio systems Rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings XLR and detachable Euro style input connectors DataPort V2 for use with DPV2-compatible signal processing accessories (XC-3, SF-3, LF-3) and DSP-3/DSP-4 (with external power supply) Independent defeatable clip limiters for reduced distortion Selectable high-pass filters protect speakers and prevent speaker transformer saturation with minimal effect on program material (30 Hz or 70 Hz on non-"Ti" models, 50 Hz or 75 Hz on "Ti" models) Front panel indicators include power, signal, and clip Covered barrier strip output connectors for safety agency compliance Automatic variable-speed fan for quiet normal operation with maximum cooling on demand Rear-to-front air flow keeps equipment racks cool Stereo, Bridge, or Parallel operating modes Comprehensive protection circuitry including DC, infrasonic, thermal overload and short circuit protection 3-year warranty plus optional 3-year extended service contract Specifications: 8 ohms 20Hz-20kHz 0.1% THD: 185W 4 ohms 20Hz-20kHz 0.1% THD: 280W 2 ohms 1kHz 1% THD: 430W 70V or 100V 50Hz-16kHz 0.5% THD: 300W 25V 50Hz-16kHz 0.5% THD: 200W Bridged Mono 8 ohms 1kHz 0.1% THD: 600W Bridged Mono 4 ohms 1kHz 1% THD: 830W 140V or 200V 50 Hz-16kHz 0.5% THD: 600W Signal to Noise (20Hz-20kHz): 100 dB Distortion (SMPTE-IM): < 0.01% Input Sensitivity @ 8 ohms: 1.15v (+3.4 dBu) Voltage Gain @ 8 ohms: 33.4x (30.5 dB) Output Circuitry: Class AB Distortion (Typical):
* 20 Hz-20 kHz: 10 dB below rated power: Less than 0.03% THD, 4 ohms and 8 ohms
* 1.0 kHz and below: full rated power: Less than 0.03% THD, 4 ohms and 8 ohms Frequency Response, 10dB below rated output power: 20Hz-20kHz, +0/-1dB, -3 dB points: 5 Hz + 50 Hz Damping Factor (Direct Outputs): > 250 @ 8 ohms Output Regulation: < 1.5 dB Input Impedance: 10 k ohms unbalanced, 20 k ohms balanced Input Clipping: 10 Vrms (+22 dBu) Cooling: Continuously variable speed fan, back-to-front air flow Connectors, each channel:
* Input: Active balanced; 3-pin Euro-style detachable terminal block and XLR (pin 2+)
* Output: Covered barrier strips
* DataPort V2: HD-15 connector Controls:
* Front: AC switch
* Rear: Ch. 1 and Ch. 2 gain knobs, 10-position DIP switch Indicators: PWR-ON Green LED, SIGNAL Green LED (1 per channel), CLIP Red LED (1 per channel) Amplifier Protection: Full short circuit, open circuit, thermal, ultrasonic, and RF protection; Stable into reactive or mismatched loads Power Requirements: 120, 230, VAC, 50-60 Hz Load Protection: On/off muting; Triac crowbar: ISA 750 Rack-mount size: 3 RU Dimensions: 19″ x 5.25″ x 15.9″ (48.3 x 13.3 x 40 cm) Weight: 44 lbs. (20 kg) หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
3
|
General Category / General Forum / QSC musicspace ISA280 Power Amp เครื่องขยายเสียง
|
on: April 01, 2015, 04:27:52 am
|
QSC musicspace ISA280 Power Amp เครื่องขยายเสียง Brand : QSC Model : ISA280 ราคาปกติ : 23,200.00 บาท000000 ราคาพิเศษ. 18,500.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เพาเวอร์แอมป์ QSC ISA280
185W @ 8 Ohms Power AmplifierDesigned as a cost-effective solution specifically for sound contractors, the ISA Series features seven models including four low impedance models (ISA 280, ISA 450, ISA 750) rated for 2-ohm operation, and three "Ti" versions with isolated 25, 70 and 100 volt outputs for distributed audio systems (ISA 300Ti, ISA 500Ti, ISA 800Ti). Versatile loading options and a comprehensive feature set make the ISA Series a rugged, cost-effective power solution for any permanently installed sound system. Unique among distributed sound power amplifiers, the "Ti" versions will drive 8- or 4-ohm loads and a distributed system on the same channel simultaneously. This enables a contractor to reduce the number of required amplifier channels by allowing a limited number of distributed speakers to be attached to the same amp as is powering the main sound system. Housed in a rugged 3 RU chassis, all seven models feature rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings. Inputs include both XLR and detachable Euro-style connectors. Outputs feature covered barrier strip connectors for safety agency compliance, and for added versatility, a DataPort V2 (Version 2) terminated with an HD-15 connector is provided for use with DPV2-compatible signal processing accessories such as the XC-3 Crossover, SF-3 Subwoofer Filter, LF-3 Low Frequency Filter and the DSP-3 with external power supply. Selectable high-pass filters are included to protect speakers and prevent speaker transformer saturation with minimal effect on program material. The ISA Series provide additional protection circuitry including DC, infrasonic, thermal overload, RF and short circuit protection. On the ISA 750 and ISA 800Ti, class H complementary bipolar output circuitry increases system efficiency by reducing AC power draw and waste heat by 40%. Cooling is accomplished via an automatic variable speed fan, which pulls air from back to front. Features: Four models for low-impedance applications Three "Ti" versions include low-impedance and isolated 25, 70, and 100 volt outputs for distributed audio systems Rear panel gain controls for tamper resistant operation with 2 dB detents for quick and repeatable settings XLR and detachable Euro style input connectors DataPort V2 for use with DPV2-compatible signal processing accessories (XC-3, SF-3, LF-3) and DSP-3/DSP-4 (with external power supply) Independent defeatable clip limiters for reduced distortion Selectable high-pass filters protect speakers and prevent speaker transformer saturation with minimal effect on program material (30 Hz or 70 Hz on non-"Ti" models, 50 Hz or 75 Hz on "Ti" models) Front panel indicators include power, signal, and clip Covered barrier strip output connectors for safety agency compliance Automatic variable-speed fan for quiet normal operation with maximum cooling on demand Rear-to-front air flow keeps equipment racks cool Stereo, Bridge, or Parallel operating modes Comprehensive protection circuitry including DC, infrasonic, thermal overload and short circuit protection 3-year warranty plus optional 3-year extended service contract Specifications: 8 ohms 20Hz-20kHz 0.1% THD: 185W 4 ohms 20Hz-20kHz 0.1% THD: 280W 2 ohms 1kHz 1% THD: 430W Bridged Mono 8 ohms 1kHz 0.1% THD: 600W Bridged Mono 4 ohms 1kHz 1% THD: 830W Signal to Noise (20Hz-20kHz): 100 dB Distortion (SMPTE-IM): < 0.01% Input Sensitivity @ 8 ohms: 1.15v (+3.4 dBu) Voltage Gain @ 8 ohms: 33.4x (30.5 dB) Output Circuitry: Class AB Distortion (Typical):
* 20 Hz-20 kHz: 10 dB below rated power: Less than 0.03% THD, 4 ohms and 8 ohms
* 1.0 kHz and below: full rated power: Less than 0.03% THD, 4 ohms and 8 ohms Frequency Response, 10dB below rated output power: 20Hz-20kHz, +0/-1dB, -3 dB points: 5 Hz + 50 Hz Damping Factor (Direct Outputs): > 250 @ 8 ohms Output Regulation: < 1.5 dB Input Impedance: 10 k ohms unbalanced, 20 k ohms balanced Input Clipping: 10 Vrms (+22 dBu) Cooling: Continuously variable speed fan, back-to-front air flow Connectors, each channel:
* Input: Active balanced; 3-pin Euro-style detachable terminal block and XLR (pin 2+)
* Output: Covered barrier strips
* DataPort V2: HD-15 connector Controls:
* Front: AC switch
* Rear: Ch. 1 and Ch. 2 gain knobs, 10-position DIP switch Indicators: PWR-ON Green LED, SIGNAL Green LED (1 per channel), CLIP Red LED (1 per channel) Amplifier Protection: Full short circuit, open circuit, thermal, ultrasonic, and RF protection; Stable into reactive or mismatched loads Power Requirements: 120, 230, VAC, 50-60 Hz Load Protection: On/off muting; Triac crowbar: ISA 750 Rack-mount size: 3 RU Dimensions: 19″ x 5.25″ x 15.9″ (48.3 x 13.3 x 40 cm) Weight: 36 lbs. (16.3 kg) หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
4
|
General Category / General Forum / QSC musicspace GXD4 Power Amplifier with DSP 1600W
|
on: April 01, 2015, 04:17:30 am
|
QSC musicspace GXD4 Power Amplifier with DSP 1600W Brand : QSC Model : GXD 4 ราคาปกติ : 26,000.00 บาท000000 ราคาพิเศษ. 22,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เพาเวอร์แอมป์ QSC GXD 4 Professional 1600W Power Amplifier with DSPThe GDX 4 from QSC may be a power electronic equipment designed for skilled PA systems utilizing speakers with four and eight ohm masses and a most output of 1600W. The GDX four employs a category D output stage with a universal power provide for prime performance and potency, whereas keeping the unit light-weight at eleven.3 lbs. The integrated DSP section includes High and Low-Pass filters (24dB LR), 4-band constant quantity equalizer, signal alignment delay, and RMS/Peak speaker protection limiting. The parallel XLR and 1/4″ TRS input connectors provide broad compatibility with convenient loop-through capabilities, whereas the skilled binding posts and NL4 instrumentation offer mono and bi-amped speaker connections. additionally to the limiting offered on inputs and outputs, the GDX employs good speaker protection by providing settings for the loudspeaker's continuous output and resistance (4 ohm or eight ohm). The GDX 4 ships with a customary IEC cord. High peak output power with up to 1600 W Power levels matched to the most popular loudspeakers and optimized for maximum real-world headroom into 4-ohm and 8-ohm speaker systems Class-D output stage with a universal power supply for high performance and efficiency Extensive built-in loudspeaker processing, includes high & low-pass filters, 4-band PEQ, limiting, and delay Large LCD display simplifies amplifier setup and indicates amp status Inputs: Parallel XLR and 1/4" TRS connectors for compatibility with any source while providing convenient loop-thru capability Precision rotary encoders for gain and DSP parameter control Outputs: Professional binding post and NL4 connectors (compatible with NL2) provide for mono and bi-amp speaker connections Digital Limiting automatically protects the amplifier from damage due to temperature rise or overdrive Adjustable speaker protection to match your loudspeaker's power and impedance Front panel LEDs indicate signal presence, input overload, and amplifier clipping Features: 1600W Max Power Output Matched for 4 Ohm and 8 Ohm Speakers Efficient Class-D Power Amplifier Built-In DSP Speaker Processor High & Low-Pass Filters with 4-Band EQ Digital Limiting with Speaker Protection LCD Display Parallel XLR and 1/4″ Inputs Binding Post and NL4 Speaker Connects Lightweight: 11.3 lbs Specifications: Watts Per Channel 8 Ohm Dynamic (Both Channels Driven): 600 W 4 Ohm Dynamic (Both Channels Driven): 800 W 8 Ohm Continuous (Both Channels Driven): 400 W 4 Ohm Continuous (Both Channels Driven): 600 W Total Harmonic Distortion (THD) Distortion: < 1% (typical), 1 kHz at full rated power Signal to Noise Ratio Signal to Noise: 100 dB, (A-weighted, 20 Hz to 20 kHz) Input Sensitivity 1.2 Vrms 3.9 Vrms Voltage Gain 33.5 dB Output Circuit Class D Power Requirements Power Requirements: 1/8 power at 4 ohms100 VAC: 3.4 A 120 VAC: 2.9 A 230 VAC: 1.6 A Frequency Response 20 Hz to 20 kHz (+0.7 dB, -0.8 dB) Headroom Dynamic Headroom: 1.25 dB (4 ohms) Damping Factor 100 Input Impedance 20 kOhms (balanced) 10 kOhms (unbalanced) Maximum Input Level +23.5 dBu Input Connectors 3-pin XLR/F 1/4″ TRS, balanced Output Connectors NL4 (Channel 1 - 1+/-, Channel 2 - 2+/-), binding posts Amplifier Protection Short circuit Open circuit Thermal RF protection Load protected against DC faults Front Panel Controls and Indicators 2 x rotary encoders 3 x operational buttons (HOME, ENTER, EXIT) 2 x green signal LEDs, indicate signal presence 2 x red A/D clip LEDs, indicate input over-drive and/or amplifier current clipping Blue power LED ring, AC on 256 x 128 Pixel LCD: 2.1 x 1.0″ / 5.4 x 2.5 cm Digital Signal Processing (DSP) High Pass Filter: 4th order LR, adjustable frequency 20 Hz to 4 kHz Low Pass Filter: 4th order LR, adjustable frequency 60 Hz to 4 kHz 4-Band PEQ: Variable frequency, gain, and bandwidth Peak Limiter: Power, aggressiveness, and impedance selection Delay: 50 ms maximum Approvals UL, CE, RoHS/WEEE compliant Dimensions (H x W x D) 3.5 x 19.0 x 10.2″ / 8.9 x 48.3 x 25.9 cm Weight 11.3 lb / 5.1 kg สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
5
|
General Category / General Forum / QSC musicspace GX5 500watt/ch 8ohms Power Amp เครื่องขยายเสียง
|
on: April 01, 2015, 04:08:53 am
|
QSC musicspace GX5 500watt/ch 8ohms Power Amp เครื่องขยายเสียง Brand : QSC Model : GX5 ราคาปกติ : 21,300.00 บาท000000 ราคาพิเศษ. 17,500.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เครื่องขยายเสียง QSC GX5
Power Amplifier Rated at 500W Per Channel @ 8 ohmsThe QSC GX5 professional power amplifier is for professional entertainers that require maximum performance and portability. This power amp is ideal for speakers in the 500 watt (Program) range, supplies maximum possible power to 4 ohm and 8 ohm loads, and features easy hookup and adjustments. Owners of popular 4 ohm loudspeakers (dual-woofer, two-way models and many subwoofers) will find the 700 watt (4 ohm) power of the GX5 an ideal match. The GX5 uses a Class H system, based on key elements of the PLX Series, almost doubling power in the same size and weight. QSC design expertise allows the output devices to shift from low-power to high-power rails in less than a millionth of a second, ensuring that the output power is always right where it needs to be without excess loss.
Uses premium toroidal power transformers for reliable "mid-weight" performance. A variable-speed fan moves air crosswise through the amplifier, drawing cool air in over the power transformer, through the fan, and then over the heat sink. This keeps the transformer cool and allows a full size heat sink to fit in a down-sized chassis. As always, the amplifiers are fully protected from the usual hazards of the trade, ensuring stable performance and long life.
GuardRail™ protection delivers full peak power while preventing detrimental overloads. During excessive clipping, or extreme overheating, GuardRail reduces gain just enough to preserve the integrity of the audio and protect the speakers without unprofessional distortion levels or shutdowns.
A subwoofer reduces strain on the full-range speaker, allowing it to play louder, or letting a smaller speaker do the same job. The GX5 supports this mode with a Crossover switch that splits the full-range input entering Ch 1, sending 20 Hz - 100 Hz to the sub (Ch 1) and 100 Hz - 20 kHz to the top box (Ch 2). The front panel gain controls balance the sub and top box, while GuardRail optimizes peak power into the sub and top individually, for greater musical impact and dynamic range. Other Features: Power levels matched to the most popular speakers used by entertainers Optimized for maximum real-world headroom into 4 ohm and 8 ohm speakersystems Inputs: XLR, 1/4″ TRS and phono input connectors for compatibility withany source Outputs: Speakon® combo accepts, 1/4″ (TS) plugs or Speakon 2-pole and4-pole plugs (connects 2 poles only). Binding posts support all other speakerwiring systems. Minimum-depth chassis fits in compact, inexpensive effects racks Detented gain controls for precise setting and matching of sensitivity Front panel LEDs monitor Power, Signal and Clipping Subwoofer/Satellite crossover built-in Specifications: 8 ohms/1 kHz (both channels driven): 500 W 8 ohms/1 kHz (single channels driven): 600 W 4 ohms/1 kHz (both channels driven): 700 W 4 ohms/1 kHz (single channels driven): 850 W Distortion (typical) 20 Hz-20kHz, 1 dB below rated power: 8 ohms: lessthan 0.05%
4 ohms: less than 0.1% Signal to Noise (20 Hz - 20 kHz): 100 dB Input Sensitivity: 1.2 Vrms Voltage Gain (8 ohms): 34.4 dB Output circuitry: 2-tier Class H Power Requirements (1/8 Power, Pink Noise @ 4 ohms,120 V): 6 A Frequency Response: 20 Hz-20kHz, +0, 1 dB Dynamic Headroom (4 ohms):2 dB Damping Factor (8ohms):100 Input Impedance(ohms):Greater than 20k (balanced) Maximum Input Level: +24dB(16 Vrms) InputConnectors(each channel): 3-pin XLR and 1/4″ TRS, balanced,parallel
Phono, unbalanced Output Connectors(eachchannel): Speakon®, 1/4″, Binding Posts Amplifier and Load Protection: Shortcircuit,open circuit, thermal, RF protection
Load protected against DC faults FrontPanelControls and Indicators: Gain controls,21detents
Red Clip LEDs, proportional, 0.1% THD threshold
GreenSignalLEDs, threshold -35 dB
Blue Power LED, AC on RearPanelControls: Full Range / Crossover switch
100 Hz,3rd order LP (sub), 2nd order HP (top) Cordset:
120V50/60 Hz:NEMA-15
230V 50 Hz: Euro 16A Dimensions: 3.5″ H x 19″ W x 10.1″ D (89 x 483x 257 mm), 2 RU High NetWeight: 26 lbs. (12 kg)
Shipping Weight: 31 lbs.(14 kg) Agency Approvals: UL, CE, RoHS/WEEECompliant สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
6
|
General Category / General Forum / QSC musicspace GP218wx Weatherized version Subwoofer Line Array Dual 18″ ลำโพง
|
on: March 31, 2015, 11:08:23 pm
|
QSC musicspace GP218wx Weatherized version Subwoofer Line Array Dual 18″ ลำโพง Brand : QSC Model : GP218-wx U.S.A. ราคาปกติ : 261,700.00 บาท000000 ราคาพิเศษ.ใบละ.. 209,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า QSC GP218-wx Weatherized SubwooferWideLine-wx models are constructed using premium birch plywood which is full encapsulated in fiberglass. The input connector plate is replaced by a hardwired, captive, UV resistant, outdoor-rated (direct burial) cable with a gland-nut through the cabinet for waterproofing. The cable will be 3 meters in length unless otherwise specified at the time the order is placed. Grilles are stainless steel covered in outdoor rated, vinyl coating and lined with acoustic foam and a fine woven stainless steel mesh. GP218-wx The GP218-wx is a weather resistant, installation version of the WideLine-10 GP218 subwoofer. The standard version includes no suspension provisions but M10 suspension points may be added on request. SPECIFICATIONS GP218-wx System Type 2 x 18″ vented subwoofer TransducersHigh-frequency Low-frequency - 2 x 18″ transducers, 4″ voice coil, ceramic magnet Frequency Response (±3 dB) 31.4 Hz - 240 Hz(without processing) Frequency Range (-10 dB) 27.4 Hz - 1.2 kHz(without processing) Continuous Power Capacity1 LF: 1700 W Peak Output 2 -LF: 140.7 dB Nominal Coverage - Input Connectors Tinned, bare wire Suspension / Attachment Points None (M10 points available by request) Weight (Net) 215 lb (97.5 kg) Dimensions (HWD) 21.13″ x 30.13″ x 47.32″537 mm x 765 mm x 1202 mm 2 Continuous IEC specified test signal, 2 hours bi-amp mode unless otherwise stated. 2 Calculated at 1 m using power capacity and system sensitivity. 6 dB peak-to-average signal ratio assumed. สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
7
|
General Category / General Forum / QSC musicspace GP218sw Wide angle Subwoofer Line Array Dual 18″ ลำโพง
|
on: March 31, 2015, 11:04:42 pm
|
QSC musicspace GP218sw Wide angle Subwoofer Line Array Dual 18″ ลำโพง Brand : QSC Model : GP218-sw U.S.A. ราคาปกติ : 131,300.00 บาท000000 ราคาพิเศษ.2สี ขาว,ดำ ใบละ.. 105,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า QSC GP218-sw WideLine™ Ground-Support Subwoofer The GP218-sw is a premium, high-performance, rectangular dual 18″ subwoofer designed for ground stacked use in the most demanding touring or installed concert applications. With an impressive combination of punch, low-frequency extension and musical accuracy, the GP218-sw is an ideal companion for the acclaimed QSC WideLine series as well as other professional sound reinforcement systems. For suspension in permanent installations each GP218-sw subwoofer comes with a total of sixteen (16) threaded M10 inserts (four per side). Features Very high acoustic output capability - 140.5 dB SPL(1m) peak Tight musical "punch" combined with low-frequency extension down to 27.4 Hz Elegant transport and handling features including an optional transport dolly plus soft cover and four thoughtfully placed handles Premium-grade, long-excursion, high-power woofers with 4″, fiberglass voice coils, double layer spiders and triple-roll surrounds 18 mm Birch ply enclosure with independent, dual chambers and extensive internal bracing for rigidity and solid, accurate reproduction SPECIFICATIONS GP218-sw Configuration 2 x 18″ vented subwoofer Transducers 8 ohm, 18″ woofer with a 4″ voice coil, ceramic magnet assembly Frequency Response (±3 dB) 31.4 Hz - 240 Hz (without processing) Frequency Range (-10 dB) 27.4 Hz - 1.2 kHz (without processing) Nominal Impedance 4 ohms Continuous Power Capacity 1700 W Recommended Power 3000 - 4000 W Sensitivity (1 W at 1 m) 101.5 dB Maximum Output - Continuous / Peak (SPL at 1 m) 134.5 dB / 140.5 dB Cabinet Type Vented, rectangular enclosure Enclosure Material Baltic birch plywood / 18 mm Grille 14 gauge powder coated steel Connectors 2 x NL4 in parallel Pin Outs Attachment Points Pins 1+/1-Sub 2+/2-NC Sixteen (16) threaded M10 inserts Weight 191 lbs (86.6 kg) Net209 lbs (94.8 kg) Shipping Dimensions (HxWxD) 20″ x 47.17″ x 30″ (508 mm x 1198 mm x 762 mm) Accessories Available (optional) CP218-0 Wood caster pallet without coverCP218-1 Wood caster pallet plus soft cover CVR-GP218 Soft cover for one GP218-sw Specifications subject to change without notice. สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
8
|
General Category / General Forum / QSC musicspace GP212 Ultra Compact Line Array Dual 12″ ลำโพง
|
on: March 31, 2015, 11:01:07 pm
|
QSC musicspace GP212 Ultra Compact Line Array Dual 12″ ลำโพง Brand : QSC Model : GP212-sw U.S.A. ราคาปกติ : 115,100.00 บาท000000 ราคาพิเศษ.2สี ขาว,ดำ ใบละ.. 92,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า QSC GP212-sw 2X12″ 1100W WideLine Ground-Support Subwoofer Black/WhiteFeatures: Very high output to size ratio - 135.4 dB SPL (1m) peak at only 15″ tall Tight musical "punch" combined with low-frequency extension down to 32 Hz Extremely low profile (15″) and small foot print Screw-in (M20) pole mount for use with full-range pole mountable speakers Elegant transport and handling features including an optional transport dolly plus soft cover and four thoughtfully placed handles Premium-grade, long-excursion, high-power woofers with 4″ voice coils 15 mm Birch ply enclosure with extensive internal bracing for rigidity and solid, accurate reproduction The GP212-sw is a premium, high-performance, rectangular dual 12″ 4th order band-pass subwoofer designed for ground stacked use in touring or installed concert applications where space constraints or enclosure size are an issue. With an impressive combination of punch, low-frequency extension and musical accuracy, the GP212-sw is an ideal companion for QSC's acclaimed WideLine series as well as other professional sound reinforcement systems. Specifications: Configuration 2 x 12″ - 4th order band-pass subwoofer Transducers 2 x 550 W, 8 ohm 12″ woofer with a 4″ voice coil, ceramic magnet assembly Frequency Response (±3 dB) 40 Hz - 100 Hz (without processing) Frequency Range (-10 dB) 32 Hz - 107 kHz (without processing) Nominal Impedance 4 ohms Continuous Power Capacity 1100 W Recommended Power 1650 - 2200 W Sensitivity (1 W at 1 m) 99 dB Maximum Output - Continuous / Peak (SPL at 1 m) 129.4 dB / 135.4 dB Cabinet Type 4th order band-pass Enclosure Material 15mm Baltic birch plywood Connectors 2 x NL4 in parallel Pin Outs Pins 1+/1-Sub2+/2-NC Attachment Points Six (6) threaded M10 inserts Weight 99.5 lbs (45.1 kg) net 115.5 lbs (52.4 kg) shipping Dimensions (HxWxD) 15″ x 20″ x 29″ (381 mm x 508 mm x 737 mm) สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
9
|
General Category / General Forum / QSC musicspace GP118sw Wide angle Subwoofer Line Array 18″ ลำโพง
|
on: March 31, 2015, 10:57:20 pm
|
QSC musicspace GP118sw Wide angle Subwoofer Line Array 18″ ลำโพง Brand : QSC Model : GP118-sw U.S.A. ราคาปกติ : 84,700.00 บาท000000 ราคาพิเศษ.2สี ขาว,ดำ ใบละ.. 68,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า QSC GP-118-sw Black/WhiteFeature Premium-grade, long excursion, high power 18-inch transducer with 4-inch voicecoil, dual layer spider and triple-roll surrounds Interlocking feet and recess features allow for rigid vertical stacking Built-in handles for ease of transport Threaded pole cup for deploying a full-range loudspeaker on top M10 fittings allows for suspension in permanent and portable applications Dual NL4 Speakon connectors 18mm Baltic birch plywood construction 16-Gauge powder coated steel grilles Available in black and white Complete EASE, CAD & BIM information available online Cinema-version available for surround LFE Specifications : System Details Frequency Response (-10dB) 29Hz - 800Hz Power Capacity1 850W (82.5V) continuous1700W peak Nominal Sensitivity2 98dB, 1W@1m Maximum Rated SPL 129dB @1m, continuous3135dB @1m, peak4 Nominal Impedance 8Ω Transducer 457mm (18-inch) driver with 102mm (4-inch) Voicecoil Recommended Power 1700W Enclosure Details Input Connector Dual NL4 connector Pin Outs 1+/1- Sub2+/2- N/C Enclosure Material 18 mm Baltic birch plywood Attachment Points 16x threaded M10 inserts Grille 16 Gauge powder coated steel Dimensions (HxWxD) 531 mm x 656 mm x 772mm (20.9″ x 25.8″ x 30.4″) Net Weight 50.3 kg (111 lb) Shipping Weight 54.9 kg (121 lb) สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
10
|
General Category / General Forum / QSC musicspace CXD4.5 4CH,1150w/ch Power Amp เครื่องขยายเสียง
|
on: March 31, 2015, 04:39:22 am
|
QSC musicspace CXD4.5 4CH,1150w/ch Power Amp เครื่องขยายเสียง Brand : QSC Model : CDX4.5 ราคาปกติ : 133,300.00 บาท000000 ราคาพิเศษ.U.S.A 107,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เพาเวอร์แอมป์ CXD4.5
4-Ch 1150W @ 4 Ohm Power AmplifierThe QSC CXD Series represents a revolutionary advancement in amplifier technology and innovation. Designed specifically for the needs of integrators, CXD provides efficient, robust and extraordinarily high fidelity power to drive multiple channels and configurations of loudspeakers while simultaneously deploying sophisticated digital processing - all with optimal energy and rack space efficiency. The CXD Series consists of three powerful, four-channel amplifiers, each with onboard DSP, and the capability to configure and combine channels in various ways to drive a wide range of loudspeaker systems including 70V and 100V without the use of transformers. These amplifiers not only provide the power and processing to make your system perform better, they offer outstanding efficiency ensuring that energy costs will be kept to a minimum over the life of the installation. Flexible Amplifier Summing Technology™ (FAST)
CXD amplifiers feature Flexible Amplifier Summing Technology™ (FAST) that actively distributes the total amplifier power in various configurations across one, two, three or all four outputs. On the CXD4.3 and CXD4.5, this power can also be used to drive 70V or 100V speaker lines directly from any one or all of the four outputs. This flexibility allows CXD Series amplifiers to drive (for example) two full-range surface mounted speakers along with a subwoofer and one 100V distributed speaker line; or a high-power subwoofer and a bi-amplified full-range loudspeaker; three 70V distributed speaker lines and a low impedance surface mount speaker line; or a single high-power channel driving monster subwoofers. Power Efficiency
CXD Series amplifiers use QSC's next generation class-D power amp design in combination with a custom power stage utilizing a new output device. These purpose built MOSFET devices provide high voltage operation without needing a full bridge output and offer better audio quality and thermal performance due to co-location of the semiconductors. CXD amplifiers benefit from the proven PowerLight power supply, made even better with Power Factor Correction (PFC) that aligns the current waveform with the AC mains voltage waveform. PFC enables CXD Series amps to draw current from the wall in a more efficient and controlled manner resulting in incredible power from a single standard AC breaker. CXD amplifiers also incorporate several energy conservation and efficiency strategies. One such tool is the unique multi-stage sleep mode that saves energy when possible without sacrificing performance. System Processing
A single CXD Series amplifier is more than just an amplifier. It is also a capable and sophisticated loudspeaker processor. Integration of DSP and amplification means that the processor knows exactly what the amplifier is doing, allowing the dynamics processing and protection circuitry to be far more accurate and effective. This synergistic approach employs both RMS and Peak Limiters that provide the amplifier and loudspeaker combination to produce more output without being pushed to distortion or destruction. The onboard DSP offers four channels of crossover filters, parametric EQ, alignment delay and dynamics processing - everything needed to optimize a loudspeaker system. Additionally when using QSC loudspeakers, the CXD amplifiers offer Intrisic Correction™, a combination of Filtering, Limiting and speaker processing first developed for our WideLine line array loudspeakers, that compensates for the non-linearities in array and horn design, resulting in exceptional performance. Space Efficient
With four channels of amplification plus signal processing in just 2RU, the CXD series replaces equipment taking up as much as three times the rack-space. Simplicity and Control
The on-board processing is managed and stored as presets, with 20 modifiable factory presets for the most common applications. A Preset Wizard is also available that simplifies amplifier setup and enables selection of loudspeakers. With an intuitive front panel UI, programming is a breeze. The CXD amplifiers also offer GPIO for system supervision and the ability to utilize contact closures to set the amps into standby or recall specific presets. With a host of integration features the CXD amplifiers are perfect for your application. Features: Flexible Amplifier Summing Technology™ (FAST) drivesmost any loudspeaker system or configuration by distributing total amplifierpower across one, two, three or all four channels. Includes 70V and 100V direct drive capability. Full function onboard loudspeaker processing DSP withCrossover and Parametric EQ Filters, Limiting and Alignment Delay eliminatethe need for outboard loudspeaker processors. PowerLight universal switchmode power supply with PFCfor highest effiency, improved audio performance, and low heat dissipation. Preset Wizard simplifies amplifier setup providingsystem design tools and loudspeaker selection from a list of speakers. Powerful Intrinsic Correction™ processing maximizesthe sonic performance of QSC loudspeakers. 20 Factory Preset configurations that can be modifiedand stored in the 50 User Presets. Integrated front panel with channel Select and Mutebuttons, Input and Output LED Metering, 400x240 LCD, intuitive navigationbuttons, LED power button and indicator, and cast aluminum handles. GPIO for additional functionality including aheartbeat output for Life-Safety supervision. Four Input Phoenix connectors, and four Phoenix touch-proof Speaker Specification: CXD4.2 CXD4.3 CXD4.5 4 Channels1 100 V rms 70 V rms 8Ω 4Ω 2Ω Burst N/A N/A 500 W 700 W 625 W Continuous 800 W˛ 800 W˛ 400 W 400 W 350 W Burst N/A N/A 900 W 1400 W 1200 W Continuous 500 W 625 W 625 W 625 W 625 W Burst N/A N/A 1200 W 2000 W 1600 W Continuous 1000 W 1250 W 1150 W 1250 W 625 W 2 Channels1 8Ω 4Ω 2Ω Burst 1200 W 1500 W 1500 W Continuous 800 W 800 W 650 W Burst 2400 W 2000 W 2500 W Continuous1250 W 1250 W 1250 W Burst 4000 W 2400 W 4000 W Continuous2250 W 2250 W 2100 W 1 Channel1 8Ω 4Ω 2Ω 1Ω Burst 1600 W 2500 W 1700 W 2500 W Continuous1500 W 1600 W 1600 W 1600 W Burst 3500 W 5000 W 3500 W 5000 W Continuous2500 W 2500 W 2500 W 2500 W Burst 4500 W 7500 W 4500 W 7500 W Continuous4200 W 4200 W 4250 W 3700 W Typical distortion 8Ω 4Ω 0.01-0.03% 0.03-0.06% 0.01-0.03% 0.03-0.06% 0.01-0.03% 0.03-0.06% Maximum distortion 4Ω-8Ω 1.0% 1.0% 1.0% Frequency response (8Ω) 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB Noise Unweighted Output Unmuted Weighted Output Muted -101 dB -109 dB -101 dB -109 dB -101 dB -109 dB Gain (1.2V setting) 34.0 dB 38.4 dB 38.4 dB Damping factor >150 >150 >150 Input impedance >10 kΩ, balanced or unbalanced >10 kΩ, balanced or unbalanced >10 kΩ, balanced or unbalanced Maximum rms input level (3.9V setting) (1.2V setting) 12.28 V (+24 dBu) 3.88 V (+14 dBu) 12.28 V (+24 dBu) 3.88 V (+14 dBu) 12.28 V (+24 dBu) 3.88 V (+14 dBu) Controls and indicators (front) Power • Channel MUTE Buttons • Channel SELECT buttons • Channel input signal and CLIP LED indicators • Channel output and LIMIT LED meters • HOME, ENTER, EXIT, GAIN navigation buttons • Control knob Controls and indicators (rear) AC power disconnect AC power disconnect AC power disconnect Rear panel connectors Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Amplifier and load protection Short circuit, open circuit, thermal, RF protection. on/off muting, DC fault shutdown, active inrush limiting, input current limiting AC power input Universal power supply 100-240 VAC, 50-60 Hz Dimensions (HWD) 3.5" x 19" x 12" (89 mm x 482 mm x 305 mm) 3.5" x 19" x 16" (89 mm x 482 mm x 406 mm) 3.5" x 19" x 16" (89 mm x 482 mm x 406 mm) Weight Net / Shipping 18.5 lb (8.4 kg) / 22 lb (10.0 kg) 21.0 lb (9.5 kg) / 25 lb (11.3 kg) 22.0 lb (10.0 kg) / 26 lb (11.8 kg) Agency approvals UL, CE, RoHS/WEEE compliant, FCC Class A (conducted and radiated emissions) Carton contents Locking IEC cable, Quick Start Guide, USB cable 1 1.0 kHz sine wave, 1% THD, all channels driven ˛ 70V & 100V are available on CXD4.2 only when channels are bridged สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
11
|
General Category / General Forum / QSC musicspace CXD4.3 4CH,625w/ch Power Amp เครื่องขยายเสียง
|
on: March 31, 2015, 04:33:26 am
|
QSC musicspace CXD4.3 4CH,625w/ch Power Amp เครื่องขยายเสียง Brand : QSC Model : CDX4.3 ราคาปกติ : 107,500.00 บาท000000 ราคาพิเศษ.U.S.A 87,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เพาเวอร์แอมป์ QSC CXD4.3
4-Ch 625W @ 4 Ohms Power AmplifierThe QSC CXD Series represents a revolutionary advancement in amplifier technology and innovation. Designed specifically for the needs of integrators, CXD provides efficient, robust and extraordinarily high fidelity power to drive multiple channels and configurations of loudspeakers while simultaneously deploying sophisticated digital processing - all with optimal energy and rack space efficiency. The CXD Series consists of three powerful, four-channel amplifiers, each with onboard DSP, and the capability to configure and combine channels in various ways to drive a wide range of loudspeaker systems including 70V and 100V without the use of transformers. These amplifiers not only provide the power and processing to make your system perform better, they offer outstanding efficiency ensuring that energy costs will be kept to a minimum over the life of the installation. Flexible Amplifier Summing Technology™ (FAST)
CXD amplifiers feature Flexible Amplifier Summing Technology™ (FAST) that actively distributes the total amplifier power in various configurations across one, two, three or all four outputs. On the CXD4.3 and CXD4.5, this power can also be used to drive 70V or 100V speaker lines directly from any one or all of the four outputs. This flexibility allows CXD Series amplifiers to drive (for example) two full-range surface mounted speakers along with a subwoofer and one 100V distributed speaker line; or a high-power subwoofer and a bi-amplified full-range loudspeaker; three 70V distributed speaker lines and a low impedance surface mount speaker line; or a single high-power channel driving monster subwoofers. Power Efficiency
CXD Series amplifiers use QSC's next generation class-D power amp design in combination with a custom power stage utilizing a new output device. These purpose built MOSFET devices provide high voltage operation without needing a full bridge output and offer better audio quality and thermal performance due to co-location of the semiconductors. CXD amplifiers benefit from the proven PowerLight power supply, made even better with Power Factor Correction (PFC) that aligns the current waveform with the AC mains voltage waveform. PFC enables CXD Series amps to draw current from the wall in a more efficient and controlled manner resulting in incredible power from a single standard AC breaker. CXD amplifiers also incorporate several energy conservation and efficiency strategies. One such tool is the unique multi-stage sleep mode that saves energy when possible without sacrificing performance. System Processing
A single CXD Series amplifier is more than just an amplifier. It is also a capable and sophisticated loudspeaker processor. Integration of DSP and amplification means that the processor knows exactly what the amplifier is doing, allowing the dynamics processing and protection circuitry to be far more accurate and effective. This synergistic approach employs both RMS and Peak Limiters that provide the amplifier and loudspeaker combination to produce more output without being pushed to distortion or destruction. The onboard DSP offers four channels of crossover filters, parametric EQ, alignment delay and dynamics processing - everything needed to optimize a loudspeaker system. Additionally when using QSC loudspeakers, the CXD amplifiers offer Intrisic Correction™, a combination of Filtering, Limiting and speaker processing first developed for our WideLine line array loudspeakers, that compensates for the non-linearities in array and horn design, resulting in exceptional performance. Space Efficient
With four channels of amplification plus signal processing in just 2RU, the CXD series replaces equipment taking up as much as three times the rack-space. Simplicity and Control
The on-board processing is managed and stored as presets, with 20 modifiable factory presets for the most common applications. A Preset Wizard is also available that simplifies amplifier setup and enables selection of loudspeakers. With an intuitive front panel UI, programming is a breeze. The CXD amplifiers also offer GPIO for system supervision and the ability to utilize contact closures to set the amps into standby or recall specific presets. With a host of integration features the CXD amplifiers are perfect for your application. Features: Flexible Amplifier Summing Technology™ (FAST) drives most any loudspeaker system or configuration by distributing total amplifier power across one, two, three or all four channels. Includes 70V and 100V direct drive. Full function onboard loudspeaker processing DSP with Crossover and Parametric EQ Filters, Limiting and Alignment Delay eliminate the need for outboard loudspeaker processors. PowerLight universal switchmode power supply with PFC for highest effiency, improved audio performance, and low heat dissipation. Preset Wizard simplifies amplifier setup providing system design tools and loudspeaker selection from a list of speakers. Powerful Intrinsic Correction™ processing maximizes the sonic performance of QSC loudspeakers. 20 Factory Preset configurations that can be modified and stored in the 50 User Presets. Integrated front panel with channel Select and Mute buttons, Input and Output LED Metering, 400x240 LCD, intuitive navigation buttons, LED power button and indicator, and cast aluminum handles. GPIO for additional functionality including a heartbeat output for Life-Safety supervision. Four Input Phoenix connectors, and four Phoenix touch-proof Speaker Specification: CXD4.2 CXD4.3 CXD4.5 4 Channels1 100 V rms 70 V rms 8Ω 4Ω 2Ω Burst N/A N/A 500 W 700 W 625 W Continuous 800 W˛ 800 W˛ 400 W 400 W 350 W Burst N/A N/A 900 W 1400 W 1200 W Continuous 500 W 625 W 625 W 625 W 625 W Burst N/A N/A 1200 W 2000 W 1600 W Continuous 1000 W 1250 W 1150 W 1250 W 625 W 2 Channels1 8Ω 4Ω 2Ω Burst 1200 W 1500 W 1500 W Continuous 800 W 800 W 650 W Burst 2400 W 2000 W 2500 W Continuous1250 W 1250 W 1250 W Burst 4000 W 2400 W 4000 W Continuous2250 W 2250 W 2100 W 1 Channel1 8Ω 4Ω 2Ω 1Ω Burst 1600 W 2500 W 1700 W 2500 W Continuous1500 W 1600 W 1600 W 1600 W Burst 3500 W 5000 W 3500 W 5000 W Continuous2500 W 2500 W 2500 W 2500 W Burst 4500 W 7500 W 4500 W 7500 W Continuous4200 W 4200 W 4250 W 3700 W Typical distortion 8Ω 4Ω 0.01-0.03% 0.03-0.06% 0.01-0.03% 0.03-0.06% 0.01-0.03% 0.03-0.06% Maximum distortion 4Ω-8Ω 1.0% 1.0% 1.0% Frequency response (8Ω) 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB Noise Unweighted Output Unmuted Weighted Output Muted -101 dB -109 dB -101 dB -109 dB -101 dB -109 dB Gain (1.2V setting) 34.0 dB 38.4 dB 38.4 dB Damping factor >150 >150 >150 Input impedance >10 kΩ, balanced or unbalanced >10 kΩ, balanced or unbalanced >10 kΩ, balanced or unbalanced Maximum rms input level (3.9V setting) (1.2V setting) 12.28 V (+24 dBu) 3.88 V (+14 dBu) 12.28 V (+24 dBu) 3.88 V (+14 dBu) 12.28 V (+24 dBu) 3.88 V (+14 dBu) Controls and indicators (front) Power • Channel MUTE Buttons • Channel SELECT buttons • Channel input signal and CLIP LED indicators • Channel output and LIMIT LED meters • HOME, ENTER, EXIT, GAIN navigation buttons • Control knob Controls and indicators (rear) AC power disconnect AC power disconnect AC power disconnect Rear panel connectors Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Amplifier and load protection Short circuit, open circuit, thermal, RF protection. on/off muting, DC fault shutdown, active inrush limiting, input current limiting AC power input Universal power supply 100-240 VAC, 50-60 Hz Dimensions (HWD) 3.5" x 19" x 12" (89 mm x 482 mm x 305 mm) 3.5" x 19" x 16" (89 mm x 482 mm x 406 mm) 3.5" x 19" x 16" (89 mm x 482 mm x 406 mm) Weight Net / Shipping 18.5 lb (8.4 kg) / 22 lb (10.0 kg) 21.0 lb (9.5 kg) / 25 lb (11.3 kg) 22.0 lb (10.0 kg) / 26 lb (11.8 kg) Agency approvals UL, CE, RoHS/WEEE compliant, FCC Class A (conducted and radiated emissions) Carton contents Locking IEC cable, Quick Start Guide, USB cable 1 1.0 kHz sine wave, 1% THD, all channels driven ˛ 70V & 100V are available on CXD4.2 only when channels are bridged สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
12
|
General Category / General Forum / QSC musicspace CXD4.2 4CH,400w/ch Power Amp เครื่องขยายเสียง
|
on: March 31, 2015, 04:29:49 am
|
QSC musicspace CXD4.2 4CH,400w/ch Power Amp เครื่องขยายเสียง Brand : QSC Model : CDX4.2 ราคาปกติ : 81,700.00 บาท000000 ราคาพิเศษ.U.S.A 66,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เพาเวอร์แอมป์ QSC CXD4.2
4-Ch 400W @ 4 Ohm Power Amplifier The QSC CXD Series represents a revolutionary advancement in amplifier technology and innovation. Designed specifically for the needs of integrators, CXD provides efficient, robust and extraordinarily high fidelity power to drive multiple channels and configurations of loudspeakers while simultaneously deploying sophisticated digital processing - all with optimal energy and rack space efficiency. The CXD Series consists of three powerful, four-channel amplifiers, each with onboard DSP, and the capability to configure and combine channels in various ways to drive a wide range of loudspeaker systems including 70V and 100V without the use of transformers. These amplifiers not only provide the power and processing to make your system perform better, they offer outstanding efficiency ensuring that energy costs will be kept to a minimum over the life of the installation. Flexible Amplifier Summing Technology™ (FAST)
CXD amplifiers feature Flexible Amplifier Summing Technology™ (FAST) that actively distributes the total amplifier power in various configurations across one, two, three or all four outputs. On the CXD4.3 and CXD4.5, this power can also be used to drive 70V or 100V speaker lines directly from any one or all of the four outputs. This flexibility allows CXD Series amplifiers to drive (for example) two full-range surface mounted speakers along with a subwoofer and one 100V distributed speaker line; or a high-power subwoofer and a bi-amplified full-range loudspeaker; three 70V distributed speaker lines and a low impedance surface mount speaker line; or a single high-power channel driving monster subwoofers. Power Efficiency
CXD Series amplifiers use QSC's next generation class-D power amp design in combination with a custom power stage utilizing a new output device. These purpose built MOSFET devices provide high voltage operation without needing a full bridge output and offer better audio quality and thermal performance due to co-location of the semiconductors. CXD amplifiers benefit from the proven PowerLight power supply, made even better with Power Factor Correction (PFC) that aligns the current waveform with the AC mains voltage waveform. PFC enables CXD Series amps to draw current from the wall in a more efficient and controlled manner resulting in incredible power from a single standard AC breaker. CXD amplifiers also incorporate several energy conservation and efficiency strategies. One such tool is the unique multi-stage sleep mode that saves energy when possible without sacrificing performance. System Processing
A single CXD Series amplifier is more than just an amplifier. It is also a capable and sophisticated loudspeaker processor. Integration of DSP and amplification means that the processor knows exactly what the amplifier is doing, allowing the dynamics processing and protection circuitry to be far more accurate and effective. This synergistic approach employs both RMS and Peak Limiters that provide the amplifier and loudspeaker combination to produce more output without being pushed to distortion or destruction. The onboard DSP offers four channels of crossover filters, parametric EQ, alignment delay and dynamics processing - everything needed to optimize a loudspeaker system. Additionally when using QSC loudspeakers, the CXD amplifiers offer Intrisic Correction™, a combination of Filtering, Limiting and speaker processing first developed for our WideLine line array loudspeakers, that compensates for the non-linearities in array and horn design, resulting in exceptional performance. Space Efficient
With four channels of amplification plus signal processing in just 2RU, the CXD series replaces equipment taking up as much as three times the rack-space. Simplicity and Control
The on-board processing is managed and stored as presets, with 20 modifiable factory presets for the most common applications. A Preset Wizard is also available that simplifies amplifier setup and enables selection of loudspeakers. With an intuitive front panel UI, programming is a breeze. The CXD amplifiers also offer GPIO for system supervision and the ability to utilize contact closures to set the amps into standby or recall specific presets. With a host of integration features the CXD amplifiers are perfect for your application. Features: Flexible Amplifier Summing Technology™ (FAST) drives most any loudspeaker system or configuration by distributing total amplifier power across one, two, three or all four channels. Full function onboard loudspeaker processing DSP with Crossover and Parametric EQ Filters, Limiting and Alignment Delay eliminate the need for outboard loudspeaker processors. PowerLight universal switchmode power supply with PFC for highest effiency, improved audio performance, and low heat dissipation. Preset Wizard simplifies amplifier setup providing system design tools and loudspeaker selection from a list of speakers. Powerful Intrinsic Correction™ processing maximizes the sonic performance of QSC loudspeakers. 20 Factory Preset configurations that can be modified and stored in the 50 User Presets. Integrated front panel with channel Select and Mute buttons, Input and Output LED Metering, 400x240 LCD, intuitive navigation buttons, LED power button and indicator, and cast aluminum handles. GPIO for additional functionality including a heartbeat output for Life-Safety supervision. Four Input Phoenix connectors, and four Phoenix touch-proof Speaker Specification: CXD4.2 CXD4.3 CXD4.5 4 Channels1 100 V rms 70 V rms 8Ω 4Ω 2Ω Burst N/A N/A 500 W 700 W 625 W Continuous 800 W˛ 800 W˛ 400 W 400 W 350 W Burst N/A N/A 900 W 1400 W 1200 W Continuous 500 W 625 W 625 W 625 W 625 W Burst N/A N/A 1200 W 2000 W 1600 W Continuous 1000 W 1250 W 1150 W 1250 W 625 W 2 Channels1 8Ω 4Ω 2Ω Burst 1200 W 1500 W 1500 W Continuous 800 W 800 W 650 W Burst 2400 W 2000 W 2500 W Continuous1250 W 1250 W 1250 W Burst 4000 W 2400 W 4000 W Continuous2250 W 2250 W 2100 W 1 Channel1 8Ω 4Ω 2Ω 1Ω Burst 1600 W 2500 W 1700 W 2500 W Continuous1500 W 1600 W 1600 W 1600 W Burst 3500 W 5000 W 3500 W 5000 W Continuous2500 W 2500 W 2500 W 2500 W Burst 4500 W 7500 W 4500 W 7500 W Continuous4200 W 4200 W 4250 W 3700 W Typical distortion 8Ω 4Ω 0.01-0.03% 0.03-0.06% 0.01-0.03% 0.03-0.06% 0.01-0.03% 0.03-0.06% Maximum distortion 4Ω-8Ω 1.0% 1.0% 1.0% Frequency response (8Ω) 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB 20 Hz-15 kHz ±0.2 dB 20 Hz-20 kHz +0.2 dB / -0.7 dB Noise Unweighted Output Unmuted Weighted Output Muted -101 dB -109 dB -101 dB -109 dB -101 dB -109 dB Gain (1.2V setting) 34.0 dB 38.4 dB 38.4 dB Damping factor >150 >150 >150 Input impedance >10 kΩ, balanced or unbalanced >10 kΩ, balanced or unbalanced >10 kΩ, balanced or unbalanced Maximum rms input level (3.9V setting) (1.2V setting) 12.28 V (+24 dBu) 3.88 V (+14 dBu) 12.28 V (+24 dBu) 3.88 V (+14 dBu) 12.28 V (+24 dBu) 3.88 V (+14 dBu) Controls and indicators (front) Power • Channel MUTE Buttons • Channel SELECT buttons • Channel input signal and CLIP LED indicators • Channel output and LIMIT LED meters • HOME, ENTER, EXIT, GAIN navigation buttons • Control knob Controls and indicators (rear) AC power disconnect AC power disconnect AC power disconnect Rear panel connectors Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Input: 3-pin Euroblock Output: 2-pin Euroblock Speaker Link: USB Type B Amplifier and load protection Short circuit, open circuit, thermal, RF protection. on/off muting, DC fault shutdown, active inrush limiting, input current limiting AC power input Universal power supply 100-240 VAC, 50-60 Hz Dimensions (HWD) 3.5" x 19" x 12" (89 mm x 482 mm x 305 mm) 3.5" x 19" x 16" (89 mm x 482 mm x 406 mm) 3.5" x 19" x 16" (89 mm x 482 mm x 406 mm) Weight Net / Shipping 18.5 lb (8.4 kg) / 22 lb (10.0 kg) 21.0 lb (9.5 kg) / 25 lb (11.3 kg) 22.0 lb (10.0 kg) / 26 lb (11.8 kg) Agency approvals UL, CE, RoHS/WEEE compliant, FCC Class A (conducted and radiated emissions) Carton contents Locking IEC cable, Quick Start Guide, USB cable 1 1.0 kHz sine wave, 1% THD, all channels driven ˛ 70V & 100V are available on CXD4.2 only when channels are bridged สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
13
|
General Category / General Forum / QSC musicspace CMX800Va Power Amp เครื่องขยายเสียง
|
on: March 31, 2015, 04:24:58 am
|
QSC CX SERIES POWER AMP เครื่องขยายเสียง Brand : QSC Model : CX SERIES ราคาปกติ : บาท ราคาพิเศษ. ตามตารางค่ะ!! .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้ารายการ รุ่น ราคาตั้ง ราคาขาย หมายเหตุ POWER AMP QSC CX 302 43,370 32,500 POWER AMP QSC CX 502 53,170 39,800 POWER AMP QSC CX 702 66,590 49,900 POWER AMP QSC CX 902 79,480 59,500 POWER AMP QSC CX 1102 88,080 66,000 POWER AMP QSC CX 302V 43,370 32,500 POWER AMP QSC CX 602V 66,590 49,900 POWER AMP QSC CX 1202V 79,480 59,500 SPECIFICATIONS CX302 CX502 CX702 CX902 CX1102 CX302V CX602V CX1202V STEREO MODE, Both Channels Driven 8 ohms, 20 Hz-20 kHz, 0.05% THD 200 W 300 W 425 W 550 W 700 W - 550 W 700 W 4 ohms, 20 Hz-20 kHz, 0.05% THD 325 W 500 W 700 W 900 W 1100 W - - 1100 W 2 ohms, 1 kHz, 1% THD 600 W 800 W 1200 W 1500 W 1700 W - - - 70V, 20 Hz-20 kHz, 0.05% THD 400 W (with IT-42*) - - 400 W 800 W 200 W 400 W 800 W 70V, 1 kHz, 0.05% THD - - - 440 W 1000 W 250 W 440 W 1000 W 70V, 1 kHz, 1% THD - - - 600 W 1200 W 300 W 600 W 1200 W BRIDGED MONO MODE 16 ohms, 20 Hz-20 kHz, 0.1% THD 400 W 600 W 850 W 1100 W 1400 W - 1100 W 1400 W 8 ohms, 20 Hz-20 kHz, 0.1% THD 700 W 1100 W 1500 W 2000 W 2200 W - - 2200 W 4 ohms, 1 kHz, 1% THD 1200 W 1600 W 2400 W 3000 W 3400 W - - - 140V, 20 Hz-20 kHz, 0.05% THD - - - 800 W 1600 W 400 W 800 W 1600 W 140V, 1 kHz, 0.05% THD - - - 880 W 2000 W 500 W 880 W 2000 W 140V, 1 kHz, 1% THD - - - 1200 W 2400 W 600 W 1200 W 2400 W Noise, 20 Hz-20 kHz >-107 dB >-107 dB >-106 dB >-106 dB >-106 dB >-106 dB >-106 dB >-106 dB Input Sensitivity @ 8 ohms 1.26 Vrms 1.23 Vrms 1.16 Vrms 1.17 Vrms 1.35 Vrms 1.26 Vrms 1.26 Vrms 1.26 Vrms Voltage Gain @ 8 ohms 30 dB 32 dB 34 dB 35 dB 35 dB 35 dB 35 dB 35 dB Output Circuitry AB+B AB+B H, 2-tier H, 2-tier H, 2-tier AB+B AB+B H, 2-tier ALL MODELS Distortion (SMPTE-IM) Less than 0.02% Distortion (Typical) 20 Hz-20 kHz: 10 dB below rated power 1.0 kHz and below: full rated power Less than 0.01% THD Less than 0.01% THD Frequency Response 20 Hz-20 kHz, +/- 0.2 dB Damping Factor Greater than 500 Input Impedance 6k ohms unbalanced, 12k ohms balanced Input Clipping 10 Vrms (+22 dB) Cooling Variable-speed fan, rear-to-front air flow Connectors, each channel Input: 3-pin XLR & 3-pin detachable terminal blocks (1 each per channel) Output: Safety-shrouded barrier strip Amplifier Protection Full short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads. Load Protection On/Off muting, DC-fault power supply shutdown Dimensions 19″ (48.3 cm) wide, 3.5″ (8.9 cm) tall (2 RU), 14″ (35.6 cm) deep (from front mounting rails) Weight 21 lbs (9.5 kg) net 27 lbs (12.3 kg) shipping สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
14
|
General Category / General Forum / QSC musicspace CMX800Va Power Amp เครื่องขยายเสียง
|
on: March 31, 2015, 04:20:36 am
|
QSC musicspace CMX800Va Power Amp เครื่องขยายเสียง Brand : QSC Model : CMX800Va ราคาปกติ : 35,000.00 บาท000000 ราคาพิเศษ.New Series 28,000.-0 .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เครื่องขยายเสียง CMX 800VA
CMX Series 2RU 800W @ 4 Ohms Stereo Power AmplifierThe CMXa series is an economical and rugged power amplifier designed to meet the needs of system integrators. It is based upon the proven, rock-solid, reliable performance found in the award winning RMX Series. The CMXa feature sets are designed for wide-ranging application in facilities such as performance halls, houses of worship, sports clubs, gymnasiums, dance venues, pubs, and FGM/BGM systems. The CMXa Series provides unmatched performance, the right power for the job and an affordable price point. Proven and Reliable Power Plant
CMXa amplifiers incorporate everything QSC has learned in more than forty years of striving to deliver worry-free operations without failures. The design of these amplifiers starts with QSC's world-class power supplies. The CMXa uses a powerful, high-current toroidal transformer and filtering to ensure generous energy reserves. This allows the amplifiers to effortlessly handle high-level transients, even when driving abusive 2 ohm speaker loads. The amplifier output sections feature rugged class AB and class H architecture depending on power level. Efficient class H output sections on the CMX 800Va reduce AC current draw and cut down on waste heat. All CMXa amplifiers are protected from damage from shorted outputs. Automatic current limiting protects the amplifier from damage until the short is corrected. CMXa amplifiers also feature DC protection systems to prevent loudspeaker damage inthe unlikely event of an output transistor failure. DC voltage from the power supply is never passed directly to your speakers, even in the event of an output circuit failure. Superior Performance
The CMXa amplifiers deliver true and accurate studio-quality sound. A full complementary output circuit using high-grade linear output devices generates accurate, flat-frequency response with low distortion. SMT (Surface Mount Technology) triples small-signal component density, enabling high power output in a 2 rack unit chassis (3 RU for the CMX 2000Va). Unlike other designs, CMXa output devices are directly mounted to the heat sink for optimum thermal coupling and cooling. The V in the model name designates the ability to directly drive 70-volt and/or 100-volt distributed loudspeakers. The CMX800Va may be used in either stereo or mono mode. For installations requiring a transformer isolated output, the CMX has optional accessories to cover your needs. Features: "Flex-Use" loading options allow you to drive low-impedance loads down to 2 ohms and certain models to drive 70 and 100V distributed loudspeaker systems "Flex-Use" Input connectivity choices including actively balanced barrier strip, XLR, or 1/4″ TRS "Flex-Use" Output connectivity choices include NL4 Speakon™ and detachable terminal block Rack mountable with chassis less than 16″ or 40.6 mm deep 1 dB recessed, detented gain controls for fast, accurate and repeatable settings Tamper-proof security cover for gain controls Recessed rear DIP switches for easy selection of stereo, parallel, or bridged mode operation, and the additional choice of enabling/disabling low frequency filter protection Low-noise variable-speed fans with rear-to-front airflow keep amplifiersand racks cool Specifications: Stereo Mode (both channels driven)
8 Ohms / FTC 20 Hz - 20 kHz/ 0.1% THD: 450W
8 Ohms / EIA 1 kHz / 0.1% THD: 500W
4 Ohms / FTC 20 Hz - 20kHz / 0.1% THD: 650W
4 Ohms / EIA 1 kHz / 0.5% THD: 800W (1% THD)
2 Ohms / EIA 1 kHz / 1% THD: 1200W
70V Direct Drive / EIA 1 kHz / 1% THD: 400W
100V Direct Drive / EIA 1 kHz / 1% THD: 1000W Bridge Mono Mode
8 Ohms / FTC 20 Hz - 20 kHz / 0.1% THD: 1300W
8 Ohms / EIA1 kHz / 0.1% THD: 1500W
4 Ohms / EIA 1 kHz / 1% THD: 2400W
70V Direct Drive/ EIA 1 kHz / 1% THD: 2000W
100V Direct Drive / EIA 1 kHz / 1% THD: 2300W Frequency Response: 20 Hz - 20 kHz: ±1 dB -3 dB points: 5 Hz - 50 kHz Damping Factor (1 kHz and below): > 300 at 8 Ohms Input Impedance: 10k ohms unbalanced, 20k ohms balanced Input Clipping: 10 Vrms (+22 dB) Cooling: Continuously variable-speed fan, rear-to-front air flow Connectors (each channel)
Input: Active balanced; barrier strip, XLRand 1/4″ (6.3 mm) - TRS tip and XLR pin 2 positive
Output: Detachable terminal block and Neutrik™ Speakon™ Controls
Front: AC switch, Ch. 1 & 2 gain knobs
Rear: 10-position DIP switch Indicators: Power-on: Green LED / Signal: Green LED (1 per channel) / Clip: Red LED (1 per channel) Amplifier Protection: Stable into reactive or mismatched load Load Protection: On/off muting, AC coupling (CMX 300Va and CMX 500Va),triac crowbar (CMX 800Va and CMX 2000Va on each channel)
Power Requirements: 120 and 230 VAC, 50 - 60 Hz Dimensions (HWD): 5.25″ 3 rack spaces x 19″ rack mounting x 15.9″ deep to rear support ears Weight: 75lbs สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
15
|
General Category / General Forum / QSC musicspace CMX800V Power Amp เครื่องขยายเสียง
|
on: March 31, 2015, 04:11:25 am
|
QSC musicspace CMX800V Power Amp เครื่องขยายเสียง Brand : QSC Model : CMX 800V ราคาปกติ : 35,000.00 บาท ราคาพิเศษ. 29,000.- .. ราคายังไม่รวมภาษีมูลค่าเพิ่ม รายละเอียดสินค้า เครื่องขยายเสียง QSC CMX800V Power Amp8ohms 500w 4 ohms 800w 2 ohms 1200w BRIDGE MONO MODE 70v/2000w 100v/2300w SPECIFICATIONS CMX300V CMX500V CMX800V CMX2000V STEREO MODE (Both Channels Driven) 8 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 185 W 200 W 260 W 300 W 450 W 500 W 1050 W 1100 W 4 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.5% THD 280 W 300 W 400 W 500 W 650 W 800 W 1600 W 2000 W (1% THD) 2 ohms EIA 1 kHz, 1% THD 430 W 700 W 1200 W 2500 W 70V Direct Drive EIA 1 kHz , 1% THD - - 400 W 2500 W 100V Direct Drive EIA 1 kHz , 1% THD - - - 1000 W BRIDGE MONO MODE 8 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 530 W 600 W 800 W 900 W 1300 W 1500 W 3200 W 3600 W 4 ohms EIA 1 kHz, 1% THD 830 W 1400 W 2400 W 5000 W 70V Direct Drive EIA 1 kHz , 1% THD 600 W 1200 W 2000 W 5000 W 100V Direct Drive EIA 1 kHz , 1% THD - 600 W 2300 W 3600 W Signal to Noise, 20 Hz-20 kHz, 8 ohms > -100 dB > -100 dB > -100 dB > -100 dB Input Sensitivity @ 8 ohms 1.15V (+3.4 dBu) 1.15V (+3.4 dBu) 1.23V (+4.0 dBu) 1.42V (+5.3 dBu) Voltage Gain @ 8 ohms 31.6x (30 dB) 40x (32 dB) 46x (33 dB) 64x (36 dB) Output Circuitry Class AB Class AB 2-tier Class H 3-tier Class H Power Requirements (120V) 1/8 power pink noise at 4 ohms 1/3 power pink noise at 4 ohms 4.4A 6.6A 5.4A 9.6A 6.3A 15.6A 13.9A 26.9A Power Requirements (230V) 1/8 power pink noise at 4 ohms 1/3 power pink noise at 4 ohms 2.2A 3.3A 2.7A 4.8A 3.2A 7.8A 7A 13.5A Distortion (SMPTE-IM) < 0.02% < 0.01% < 0.01% < 0.01% ALL MODELS Distortion (Typical) 20 Hz - 20 kHz: 10 dB below rated power 1.0 kHz and below: full rated power Less than 0.03% THD, 4 and 8 ohms Less than 0.03% THD, 4 and 8 ohms Damping Factor, 1 kHz and below Greater than 300 at 8 ohms Input Impedance 10k ohms unbalanced, 20k ohms balanced Input Clipping 10 Vrms (+22 dB) Cooling Continuously variable-speed fan, rear-to-front air flow Connectors, each channel Input: Active balanced; barrier strip, XLR and 1/4″ (6.3mm) TRS tip and XLR (pin 2 positive) Output: detachable terminal block and Neutrik™ Speakon™ Controls Front: AC switch, Ch. 1 and Ch. 2 gain knobs Rear: 10-position DIP switch Indicators Power-On: Green LED Signal: Green LED (1 per channel) Clip: Red LED (1 per channel) Amplifier Protection Stable into reactive or mismatched loads Load Protection On/off muting, AC coupling (CMX300V, CMX500V), triac crowbar (CMX800V, CMX2000V, on each channel) Power Requirements 120, 230 VAC, 50-60 Hz Dimensions (HWD) 2RU Models3RU Model (CMX2000V) 3.5″ (8.9 cm) 2 rack spaces x 19″ (48.3 cm) rack mounting x 15.9″ (40 cm) deep to rear support ears 5.25″ (13.3 cm) 3 rack spaces x 19″ (48.3 cm) rack mounting x 15.9″ (40 cm) deep to rear support ears Weight - net 35 lbs (15.9 kg) 40 lbs (18.2 kg) 44.5 lbs (20.2 kg) 75 lbs (33.1 kg) Weight - Shipping 41 lbs (18.6 kg) 46 lbs (20.9 kg) 50.5 lbs (23 kg) 87 lbs (37.2 สบถามได้ที่ หรือสั่งซื้อได้ที่ Musicspace.co.th
|
|
|
|